As one of the most core forming processes in the field of mechanical manufacturing, milling machine machining can efficiently process flat surfaces, grooves, gears, curved surfaces, and complex three-dimensional structures by rotating multi blade cutting tools to remove material layer by layer from the workpiece. The quality and efficiency of milling machining highly depend on the performance of various system components of the milling machine - the high-speed dynamic characteristics of the spindle, the clamping stiffness of the tool system, the response speed of the feed system, and the load-bearing and indexing accuracy of the worktable jointly determine the machining capacity boundary. This article systematically analyzes the specific applications of key components such as spindle units, cutting tools and tool holder systems, feed transmission components, guide rail systems, workbenches and rotary indexing devices, and cooling chip removal systems in milling machine processing. It explores the coupling relationship between component accuracy and milling technology, and combines the development trends of high-speed milling, five axis linkage, and intelligent machining to look forward to the technological evolution direction of components, providing reference for milling machine design and process optimization.


10.jpg


1. Introduction

Milling machine is one of the most widely used metal cutting machine tools, and its machining principle is to use high-speed rotating milling cutters to cut workpieces fixed on the worktable. Unlike lathes, which mainly process rotating parts, milling machines can handle flat surfaces, contours, cavities, gears, threads, and various complex spatial surfaces. They play an irreplaceable role in mold manufacturing, aerospace structural components, automotive powertrains, electronic equipment casings, and medical devices.

The milling process presents three significant characteristics: firstly, the cutting process exhibits intermittent cutting characteristics, with each tooth periodically cutting in and out, generating periodic impact loads on the tool system and spindle bearings; Secondly, there is a significant difference in material removal rates, spanning three orders of magnitude from micro cutting in precision milling (single cut depth of 0.01mm) to heavy-duty rough milling (cut depth of over 10mm); Thirdly, five axis linkage milling requires precise coordination of multiple motion axes on spatial trajectories, which puts extreme demands on the dynamic response and reverse clearance control of transmission components.

The above characteristics determine that the design and selection of milling machine components must comprehensively consider stiffness, vibration resistance, thermal stability, and long-term accuracy maintenance. The ceiling of milling machine processing capability often lies not in the numerical control system, but in the physical limits of key components such as spindle bearings, ball screws, linear guides, and tool holder interfaces. Therefore, a deep understanding of the application logic of components in milling machine processing has important engineering value for improving milling efficiency, controlling processing costs, and ensuring product quality.

2、 The core requirements of milling machine processing for components

2.1 High static stiffness and dynamic stiffness

During the milling process, the magnitude and direction of the cutting force vary periodically with the cutting of the teeth. Taking typical face milling as an example, each tooth produces an impact when cutting into the workpiece, and the load is suddenly relieved when cutting out, resulting in excitation frequencies ranging from tens of hertz to thousands of hertz. If the stiffness of the spindle system, tool holder, or worktable is insufficient, forced vibration or even chatter will occur under the action of excitation force, resulting in vibration patterns on the machined surface, tool breakage, and premature failure of the spindle bearings.

The dynamic stiffness depends on the static stiffness, damping ratio, and mass distribution. In practical applications, measures such as increasing the outer diameter/inner diameter ratio of the spindle sleeve, using short cone double-sided contact tool holders (such as HSK, Capto), and increasing the thickness of the worktable reinforcement plate can effectively improve the anti vibration performance.

2.2 High positioning accuracy and repetitive positioning accuracy

The positioning accuracy of a CNC milling machine determines the relative positional accuracy between machining features. Taking the processing of box parts with hole systems as an example, the hole spacing tolerance is usually required to be within ± 0.01mm, which requires the ball screw system to have almost zero backlash error (backlash) during reverse motion, and also requires the resolution of measuring components such as grating rulers to reach the micrometer level. The repeated positioning accuracy affects the consistency of batch production - when processing 100 parts on the same milling machine, the coordinate difference of the same positioning feature on each part must be within the tolerance range.

2.3 High speed operation capability

With the popularization of high-speed cutting technology, the spindle speed of modern milling machines has jumped from the traditional 4000-6000r/min to 15000-4000r/min, and some micro milling machines even reach over 80000r/min. High speed operation has put forward new requirements for the centrifugal force management of bearings, the dynamic balance level of tool holders, and the heat dissipation design of spindle motors. When the spindle speed exceeds 20000r/min, even a small unbalanced mass (0.1g · mm) will generate a centrifugal force of tens of newtons, causing significant vibration.

2.4 Thermal Symmetry and Thermal Compensation Capability

The heat source in milling processing is complex, including friction heat from spindle bearings, motor heating, cutting heat transfer, and environmental temperature changes. Multi axis milling machines are particularly sensitive - milling machines with C-shaped column structures, when the spindle box moves up and down on the column, there is a temperature difference between the front and back of the column, causing the column to bend and deform, directly affecting the perpendicularity of the spindle axis and the worktable. The component design adopts a thermal symmetric structure (such as double column gantry structure, box in box structure) and integrates temperature sensors and thermal compensation algorithms, which has become a standard configuration for high-end milling machines.

3、 The specific application of core components in milling machine processing

3.1 Spindle unit components

The spindle is the power output core of the milling machine, and its components mainly include the spindle body, bearings, puller mechanism, spindle motor, and cooling sleeve.

The configuration of spindle bearings directly affects the maximum speed and stiffness. For a universal vertical milling machine, the front support adopts a back-to-back configuration of two angular contact ball bearings (DB combination), and the rear support adopts a double row cylindrical roller bearing. This configuration can withstand both radial and bidirectional axial forces, while allowing the spindle to elongate towards the rear end after being heated. For high-speed milling centers, hybrid ceramic bearings (steel rings+Si ∝ N ₄ ceramic balls) have become the mainstream choice - the density of ceramic balls is only 40% of that of steel balls, the centrifugal force is significantly reduced during high-speed operation, and the thermal expansion coefficient is small, resulting in better temperature rise control. Test data shows that under the condition of d · n value (product of bearing pitch diameter and rotational speed) reaching 2 × 10 ⁶ mm · r/min, the temperature rise of hybrid ceramic bearings is 15-20 ℃ lower than that of all steel bearings.

The built-in electric spindle directly presses the motor rotor onto the spindle core shaft, and the stator is enclosed in the spindle box, achieving zero transmission, high speed, and low vibration. The internal component layout of an electric spindle is extremely compact, usually including three-phase windings, a rotary transformer (or encoder), temperature sensors, vibration sensors, a puller mechanism (disc spring group), and a cooling spiral water channel. Taking a certain model of 18kW electric spindle as an example, the vibration value at 24000r/min is controlled within 0.6mm/s, and the radial static stiffness reaches 120N/μ m, which can stably cut hardened steel (HRC52).

The pulling mechanism is responsible for the automatic clamping and releasing of the cutting tool, and the disc spring group is the core component. A set of disc springs in series/parallel combination generates a pulling force of 5000-15000N under compression, ensuring a tight fit between the taper surface of the tool holder and the taper hole of the spindle. When loosening the tool, the hydraulic or pneumatic cylinder pushes the top rod to compress the disc spring and release the tool. The fatigue life of the disc spring directly determines the reliability of the automatic tool changing system. High end milling machines require the compression rebound cycle of the disc spring to reach more than 2 million times.

3.2 Tool system and tool holder components

The performance of the milling cutter system depends on the geometric parameters of the tool, the coating material, and the interface form of the tool holder.

The handle is a key component that connects the tool and the spindle. The traditional BT handle (7:24 taper single-sided contact) expands the taper hole during high-speed rotation, resulting in changes in axial position and a decrease in stiffness. The new HSK handle (1:10 hollow short cone double-sided contact) solves this problem: the hollow cone handle slightly expands radially under centrifugal force, which actually makes the contact between the cone surface and the end face more tight. The HSK-E63 tool holder maintains an interference fit of 3-5 μ m at 25000 r/min, enabling high-precision repetitive positioning. The Capto interface adopts a triangular cross-section, which can transmit greater torque and is suitable for heavy-duty milling and multitasking machine tools.

The milling cutter head and blade are both consumable components. The corn milling cutter (reversible spiral end mill) is equipped with multiple rows of hard alloy inserts on the cutting body, and the single cutting depth during rough machining can reach 8-10mm, with a material removal rate of up to 300cm ³/min. The positioning accuracy of each blade is determined by the grinding accuracy of the blade groove and the torque of the clamping screw. If the blade is 0.02mm higher than the set value, the cutting force of the tooth will increase by more than 30%, causing periodic vibration. High end rotatable cutting tools use precision ground grooves and torque wrenches to control the radial runout of all teeth within 0.01mm.

3.3 Feed transmission components

The feed system converts the rotational motion of the servo motor into linear motion of the worktable or spindle box, with core components including ball screw pairs, screw support bearings, couplings, and nut seats.

The accuracy level of the ball screw directly determines the positioning accuracy of the milling machine. The C3 level screw (with a variation of ≤ 8 μ m within any 300mm stroke) coupled with a grating ruler fully closed-loop control can achieve a positioning accuracy of 5 μ m/300mm for a three-axis milling machine. During operation, the screw generates heat due to friction, resulting in thermal elongation. A 1.2m long screw can elongate by 0.14mm at a temperature difference of 10 ℃, which is sufficient to exceed the machining size tolerance. One solution is to pass cooling oil inside the screw (hollow screw technology) to control the temperature rise within 2 ℃; The second is to apply pre tension (usually 0.04-0.06mm per meter) to the screw to maintain its design length in thermal equilibrium.

The screw support bearing is mainly a thrust angle contact ball bearing with a contact angle of 60 °. It is usually installed back-to-back with appropriate pre tension to eliminate axial clearance. If the preload force is too large, the bearing will heat up severely, and if it is too small, the axial stiffness will be insufficient. In practical applications, the preload force is calculated based on the bearing size and screw diameter. For example, for a 32mm diameter screw with a 7206 bearing, the preload force is set to 1500-2000N.

Linear motors are replacing ball screws as the feed solution for high-speed milling machines. The primary (rotor) of the linear motor is directly installed on the worktable, and the secondary (permanent magnet stator) is fixed on the bed, eliminating the elastic deformation, reverse clearance, and frictional wear of the lead screw. The acceleration can reach 2-3g, and the maximum feed rate can reach 120m/min. But linear motors do not generate self-locking force and must be equipped with high-resolution grating rulers (0.1 μ m) and power-off brakes, with higher component complexity than screw solutions.

3.4 Components of the guide rail system

The guide rail supports the moving parts and ensures motion accuracy, with key components including the guide rail body, slider, rolling element, and seal.

Roller linear guides have become the mainstream choice for milling machines due to their high contact stiffness (approximately 1.5 to 2 times that of ball guides). The rollers make cyclic motion inside the slider, and their rolling contact reduces sliding friction to rolling friction (friction coefficient 0.002-0.004), without crawling phenomenon. Taking the 55 specification roller guide as an example, the rated dynamic load of a single slider can reach 80kN, which is sufficient to support a worktable weighing up to 5 tons. Pre pressing levels are divided into light pre pressing (Z0), medium pre pressing (Z1), and heavy pre pressing (Z2). Milling machining usually uses Z1 level or above to improve system stiffness.

On large gantry milling machines, static pressure guide rails are applied to the crossbeam and slider components. Inject high-pressure oil (5-15MPa) into the oil chamber on the guide rail surface to suspend the slider by 0.02-0.05mm, achieving non-contact motion with a friction coefficient as low as 0.0005. The oil film of the static pressure guide rail has a very high damping ratio (0.1-0.2), which can effectively absorb cutting vibrations and is suitable for precision mold milling. But its component composition is complex, including oil pump, accumulator, throttle, filter, and pressure sensor for each oil chamber, resulting in high maintenance costs.

3.5 Workbench and indexing device components

The worktable carries the workpiece and is positioned during machining. For multi axis milling machines, the worktable itself contains rotating and swinging components.

The core component of the CNC turntable (fourth axis) is the worm gear pair or torque motor. The traditional dual lead worm drive can achieve zero backlash adjustment, with a division accuracy of ± 15 arc seconds, but the transmission efficiency is relatively low (about 50% to 70%), and wear is fast during high-speed rotation. The direct drive torque motor turntable eliminates mechanical transmission components and is directly installed on the rotor of the motor, with a maximum speed of 200r/min and a division accuracy of ± 5 arc seconds. However, it requires the configuration of high-precision circular gratings (such as the Heidenhain RCN series) and strong brakes.

The swing head and turntable of a five axis milling machine contain more complex components. The cradle style five axis worktable includes an A-axis (swing) and a C-axis (rotation), both of which are supported by crossed roller bearings and have extremely high overturning stiffness. The swing type five axis is achieved by swinging on the spindle side, and the worm gear or torque motor inside the fork shaped component needs to have anti fall braking function to ensure that the spindle will not slide down and hit the workpiece in case of sudden power failure.

3.6 Cooling and chip removal components

Milling, especially rough machining, generates a large amount of chips and cutting heat, and the cooling and chip removal system components directly affect machining continuity and environmental hygiene.

The spindle center water discharge (CTS) system sends high-pressure cutting fluid (3-15MPa) into the spindle inner hole through a rotary joint, and sprays it out from the tool end face through the cold hole in the tool holder, directly reaching the cutting area. The rotary joint is a critical component that needs to maintain sealing under high-speed rotation of the spindle, with a leakage rate controlled within 10ml/min. The CTS system can increase tool life by 1-3 times, especially suitable for deep cavity milling and difficult to machine materials (titanium alloys, high-temperature alloys).

The chip conveyor is the core component of automation. The chain plate type chip conveyor is suitable for processing a large amount of long chips (such as steel parts), and its stainless steel chain plate is driven by a reduction motor to transport the chips to the chip collection vehicle. The spiral chip conveyor has a simple structure and is suitable for powder cutting or dry cutting conditions. For a five axis milling machine, due to the complex movement of the worktable, a multi-stage chip removal system is often used - flushing nozzles are installed around the worktable to flush the chips into the bottom spiral chip removal device, and then lift them to the chain plate chip removal device.

4、 The coupling relationship between component accuracy and milling process

The accuracy of the components ultimately needs to be verified through the process effect. Taking the cavity milling of mold steel (such as P20, HRC32) as an example, if the wear of the spindle bearing causes the radial runout to increase from 2 μ m to 6 μ m, when using a 12mm diameter ball end milling cutter for precision machining, the surface roughness Ra will increase from 0.4 μ m to 0.8-1.0 μ m, which is beyond the acceptable range of the mold polishing process and requires additional semi precision machining or manual polishing time.

The wear of ball screws also affects the process. When the pre tightening force of the screw nut decreases by 20% due to wear and the reverse clearance increases from 2 μ m to 6 μ m, there will be a noticeable tool step when milling parts with vertical walls. In a certain aviation blade processing case, due to the Z-axis lead screw clearance exceeding the tolerance, the contour of the blade root and tip deviated by 0.025mm and 0.035mm respectively, resulting in the scrapping of the parts.

From an economic perspective, the selection of component accuracy levels should be balanced between process requirements and costs. The price of P4 grade spindle bearings is about 1.8 times that of P5 grade, but the service life is extended by 40%. For production lines with a batch size exceeding 5000 pieces, choosing a higher precision level to dilute the cost to individual pieces is often lower.

5、 Component innovation under the trend of intelligent manufacturing

5.1 Intelligent spindle and status monitoring

The modern milling machine spindle integrates temperature, vibration, and displacement sensors to monitor real-time changes in bearing preload force, unbalance growth, and tool clamping status. When there is an abnormal increase in the amplitude of the bearing characteristic frequency (such as the rolling element passing frequency) in the vibration spectrum, the system will prompt maintenance. In a practical case, the intelligent spindle issued a warning 50 hours before the bearing was damaged, avoiding serious damage to the workpiece and equipment caused by spindle jamming.

5.2 Thermal compensation components

Thermal deformation is one of the main sources of error affecting the accuracy of milling machines. The design of new components emphasizes heat source isolation and thermal symmetry. For example, the Z-axis slider adopts a "box in box" structure, with cooling medium or insulation material filled between the inner and outer walls; The screw nut seat integrates temperature sensors and cooling channels, and the control system compensates for motion commands in real-time based on temperature feedback. Experimental results have shown that in an environment with a temperature change of ± 5 ℃ in the workshop, milling machines using thermal compensation measures can reduce dimensional drift from 0.03mm to 0.008mm within 24 hours.

5.3 Additive Manufacturing of Lightweight Components

3D printing technology is used for the manufacturing of milling machine components, especially for moving parts such as five axis swing heads and cradle turntables, with significant effects. The topology optimized swing fork shaped component is achieved through additive manufacturing, reducing weight by 35% while maintaining the same stiffness, resulting in a 30% improvement in the acceleration and deceleration performance of the rotating shaft. At the same time, additive manufacturing can integrate the formation of internal cooling channels, solving the problem that traditional casting cannot achieve complex channels.

VI. Conclusion

The application of components in milling machine processing runs through all subsystems such as spindle, tool holder, feed, guide rail, worktable, cooling and chip removal. The accuracy and stiffness of the spindle bearings determine the maximum speed and anti vibration ability of milling; The positioning performance of ball screws and linear guides constrains the geometric accuracy of milling machines; The form of the tool holder interface affects the safety and stability of high-speed cutting; The cooling and chip removal components are the guarantee for automated continuous operation.

With the promotion of advanced processes such as high-speed milling, five axis linkage, and dry cutting, components are developing towards higher speeds, higher stiffness, intelligence, and thermal stability. Innovative technologies such as intelligent spindles with built-in sensors, direct drive torque motor turntables, all ceramic bearings, and additive manufacturing of lightweight components are constantly emerging. For milling machine manufacturing enterprises and process personnel, a deep understanding of the performance characteristics of components, scientific formulation of assembly accuracy and selection strategies, is the core path to enhance milling competitiveness and achieve high-precision and high-efficiency machining. In the future, with the deep integration of digital twins, artificial intelligence, and component technology, milling machines will have more complete self-awareness and adaptive capabilities, driving mechanical manufacturing to new heights.


Tel
15921227578 Liu Jinlin
Landline:021-69176937
Email
jinlinliu@bmzpmw.com
Headquarters Base
No. 58, Lane 355, Shengxin South Road, Nanxiang Town, Jiading District, Shanghai
Taicang Base
About 60 meters northeast of the intersection of Taicang City Pai Xin Chang Line and Xingang Road in Suzhou City
Customer Service WeChat
Copy successful
Contact
We are right beside you
Add WeChat and let us know your needs
Tel
15921227578
Top
Copy successful

WeChat ID: 400-000-8888

Add WeChat friends to get free
solutions and quotes

OK