Wire cutting has an irreplaceable position in the fields of precision component manufacturing, mold processing, and difficult to cut material forming due to its non-contact cutting, no macroscopic cutting force, high precision, and high surface quality. The processing capability of wire cutting equipment highly depends on the performance matching and coordination of key components such as electrode wires, wire guides, working fluid circulation systems, wire transport mechanisms, numerical control systems, and high-frequency pulse power supplies. This article systematically analyzes the specific applications of electrode wire, guide wire device, working fluid and filtration system, wire transport transmission components, tension control mechanism, and high-frequency power module in online cutting and processing. It explores the impact mechanism of component accuracy on cutting quality, processing efficiency, and electrode wire loss, and combines the development trends of intelligence, high-speed, and miniaturization to look forward to the technological evolution direction of wire cutting components.


11.jpg


1. Introduction

Wire EDM is a special form of electrical discharge machining, which can be traced back to the 1960s. After decades of development, it has become an indispensable machining method in the field of precision manufacturing. Unlike traditional metal cutting, wire cutting uses the instantaneous high temperature (up to 8000-12000 ℃) generated by discharge to melt or even vaporize the workpiece material. Therefore, it can process any conductive material without being limited by material hardness - quenched steel, hard alloys, titanium alloys, high-temperature alloys, and even conductive ceramics can be precision contour cut.

The unique advantages of wire cutting machining are: firstly, no macroscopic cutting force, low residual stress in the workpiece, suitable for machining thin-walled parts, microstructures, and easily deformed parts; Secondly, the cutting gap is narrow (usually 0.10-0.35mm), which can process small inner contours and fine shapes; Thirdly, it is capable of processing difficult to cut materials with high hardness, brittleness, and toughness; Fourthly, the processed surface has almost no deteriorated layer and can achieve a surface roughness of Ra 0.2-0.8 μ m, which can sometimes be used as the final processing step.

The implementation of the above excellent performance highly relies on the precise coordination of various system components of the wire cutting equipment. The material, diameter, and coating of the electrode wire determine the cutting efficiency and surface quality; The accuracy of the V-shaped groove of the wire guide (guide wheel and guide) directly affects the positional accuracy of the cutting path; The conductivity, filtration accuracy, and cooling performance of the working fluid affect the discharge stability and chip removal effect; The constant tension and stable wire speed of the wire transport mechanism are the basis for obtaining uniform cutting seam width. The performance degradation of any component will be directly reflected as a decrease in cutting accuracy, deterioration of surface roughness, or a decrease in processing efficiency.

With the increasing demand for small precision parts in aerospace, the increasing demand for mold accuracy in the electronics industry, and the tightening of surface quality standards for medical devices, wire cutting machining is developing towards "higher efficiency, higher precision, smaller wire diameter, and more intelligence". This article will systematically explain the functional positioning, technical requirements, and application practices of various components in online cutting processing from the perspective of core components.

2、 The core requirements of wire cutting processing for components

2.1 Material stability and geometric consistency of electrode wires

Electrode wire is a component directly involved in discharge in wire cutting machining, and its material composition, tensile strength, elongation, surface coating, and diameter tolerance jointly determine the machining effect. Taking high-speed wire cutting as an example, electrode wires need to withstand frequent discharge shocks and thermal deformations during the machining process, while also maintaining good tensile performance during high-speed reciprocating motion. The uniformity of electrode wire diameter directly affects the consistency of cutting seam width - if the diameter deviation exceeds ± 0.002mm, it will cause over cutting or under cutting when cutting small corners of precision molds. Therefore, electrode wires are both consumables and strategic components that determine processing quality.

2.2 High wear resistance and positioning accuracy of guide wire system

The guide wire system includes components such as upper guide wheels, lower guide wheels, guides, and conductive blocks. The electrode wire experiences rolling friction with the V-shaped groove of the guide wheel during high-speed movement. Insufficient wear resistance of the guide wheel material can cause wear on the V-shaped groove, resulting in lateral oscillation of the electrode wire during movement and a decrease in cutting accuracy. For slow wire cutting, the accuracy of the wire guide is even more demanding - the roundness and surface roughness of the diamond guide's inner hole directly determine the guiding accuracy of the electrode wire. Any internal hole scratches or aperture deviations can lead to wire breakage or cutting size deviation.

2.3 Cleanliness control of working fluid circulation filtration system

Working fluid plays multiple roles in online cutting processing, including insulation, cooling, chip removal, and recovery of dielectric breakdown strength. The electrochemical corrosion products (micro - and sub micron sized metal particles) generated during processing are suspended in the working fluid. If not filtered out in a timely manner, it can lead to secondary discharge and abnormal discharge, resulting in stripes on the cutting surface, decreased processing speed, and even short circuits. The filtration accuracy of the filter element in the filtration system, the flow stability of the circulation pump, and the exchange capacity of the deionized resin directly affect the cleanliness of the working fluid, thereby affecting the stability of the processing quality.

2.4 Constant tension and smooth motion of the wire transport mechanism

The tension and fluctuation of the electrode wire are key factors affecting the cutting seam width and surface roughness. Excessive tension intensifies the elastic deformation of the electrode wire, making it prone to wire breakage and exerting excessive pressure on the guide wheel; The tension is too low, and the electrode wire is prone to deviate from the theoretical position under the action of discharge explosion force, causing distortion of the cutting path. For high-speed reciprocating wire walking (fast wire walking), the tension fluctuation of the electrode wire is particularly severe at the moment of commutation, and it is necessary to absorb the impact through a precisely designed tension adjustment mechanism and counterweight system. Slow wire walking requires tension error control within ± 0.5g, which places extremely high demands on the response speed of tension sensors and servo control components.

3、 Specific Applications of Online Cutting Processing for Core Components

3.1 Electrode wire components

As a tool for directly performing discharge cutting, the material, structure, diameter, and surface characteristics of electrode wires have a decisive impact on the machining results. According to the different wire walking methods, electrode wires are divided into fast wire electrode wires (molybdenum wire) and slow wire electrode wires (brass wire, galvanized wire, diffusion annealed wire, etc.).

Molybdenum wire is a unique fast wire electrode wire in China, which has become the preferred material due to its high melting point (2620 ℃), high tensile strength (about 1500N/mm ²), and good conductivity. The diameter specifications of molybdenum wire range from 0.10mm to 0.22mm, with 0.18mm being the most widely used. The manufacturing process of molybdenum wire includes multiple steps such as vertical melting sintering, rotary forging, wire drawing, and straightening. The final product requires a diameter tolerance of no more than ± 0.001mm and an ellipticity control within 0.5 μ m. In high-speed wire cutting, molybdenum wire moves back and forth at a speed of 8-12 m/s, with a single processing life of about 6-10 hours. The main form of wear of molybdenum wire is diameter reduction caused by discharge erosion. When the wear amount reaches 15% of the original diameter, it should be replaced, otherwise the cutting accuracy cannot be guaranteed.

Huangtong wire is the most basic electrode wire material for slow wire cutting, made of copper zinc alloy (with a copper content of about 65%) through precision drawing. The cutting efficiency of brass wire is relatively high, but the zinc element is prone to volatilization at high temperatures, causing pollution to the working fluid. The galvanized electrode wire developed on this basis improves the concentration and stability of discharge by coating a layer of pure zinc or zinc oxide on the surface of the brass core wire. The cutting speed is increased by 20% to 30% compared to ordinary brass wire, and the surface roughness is reduced by about 15%. The diffusion annealed electrode wire adopts a special heat treatment process to form a diffusion alloy layer between the core wire and the coating. The heat resistance and wire breakage resistance of the electrode wire are further improved, making it suitable for processing workpieces with a thickness exceeding 200mm or for multiple cutting and finishing.

In the field of micro wire cutting, tungsten wire is an ideal choice for micro electrode wires with diameters ranging from 0.02 to 0.07mm due to its extremely high tensile strength (over 3000N/mm ²) and good conductivity. When using tungsten wire to process narrow grooves and small holes in micro molds, the cutting seam width can be controlled within 0.05mm, and the corner radius can reach 0.025mm. However, tungsten wire is expensive and brittle, requiring extremely high precision of wire components and the experience of operators.

3.2 Components of guide wire device

The guide wire device is responsible for guiding and supporting the movement of the electrode wire, and its key components include guide wheels, guides, conductive blocks, and shock absorbers.

Guide wheels are divided into ceramic guide wheels, hard alloy guide wheels, and gemstone guide wheels according to their materials. High speed wire cutting commonly uses hard alloy guide wheels, with a V-shaped groove hardness of HRA89-91, good wear resistance, and a service life of about 1000 hours. The contour accuracy of the V-shaped groove directly determines the straightness of the electrode wire movement - the V-shaped angle is usually 90 °± 15 ′, the groove bottom fillet R0.1-0.2mm, and the surface roughness Ra ≤ 0.2 μ m. When visible wear marks appear on the V-shaped groove of the guide wheel, the electrode wire will undergo periodic oscillation, and the straightness error of the cutting surface can be expanded from 0.005mm to 0.02mm.

The guide of slow wire cutting is one of the most accurate components, usually made of natural diamond or polycrystalline diamond. There is a precision machined micro hole in the center of the guide (with a diameter only 0.005-0.015mm larger than the electrode wire diameter), and there is almost no radial gap when the electrode wire passes through it. Taking the processing of 0.25mm diameter brass wire as an example, the inner hole diameter of the diamond guide is 0.255-0.260mm, and the cylindricity of the inner hole is controlled within 0.001mm. The precision retention time of the guide is about 2000-3000 hours, after which the inner hole wears out and the electrode wire outlet position drifts, requiring replacement.

The conductive block is responsible for reliably transferring the energy of the pulse power supply to the electrode wire. The commonly used conductive block material is copper tungsten alloy (containing 20% to 30% copper and 70% to 80% tungsten), which balances the good conductivity of copper and the high arc erosion resistance of tungsten. The contact between the conductive block and the electrode wire can be divided into two types: sliding contact and rolling contact. The continuous friction between the sliding contact conductive block and the electrode wire will gradually form discharge corrosion pits on the surface of the conductive block, and the contact position needs to be adjusted or replaced regularly; Rolling contact type uses conductive rollers, which have less wear but a complex structure.

3.3 Working fluid and circulating filtration system components

The performance requirements of the working fluid for wire cutting machining are much higher than those for traditional electrical discharge machining. Slow wire cutting uses deionized water as the working fluid, and its core components include a deionized resin exchange tank, precision filter, circulation pump, and constant temperature device.

Deionization resin adsorbs metal ions in the working solution through ion exchange reaction, and controls the conductivity within the ideal range of 5-20 μ S/cm. When the conductivity is too high, the insulation performance of the working fluid decreases, the discharge channel is difficult to form, and the processing is unstable; When the conductivity is too low, the discharge gap is too small and it is easy to short circuit. Resin exchange tanks usually adopt a dual tank parallel design, with one tank in operation and one tank for regeneration or backup. The exchange capacity of resin is about 1.2-1.5 eq/L. When the effluent conductivity exceeds the set value, the system automatically alarms and prompts to replace the resin.

Filters are used to capture erosion products and resin debris, and their filtration accuracy directly affects surface quality. During the rough machining stage, filter cartridges with a precision of 10-20 μ m are used, while during the finishing stage, filter cartridges with a precision of 1-5 μ m are used. Folding microporous filter cartridges are widely used due to their large filtration area and strong pollutant holding capacity. Taking a slow wire feeder as an example, when equipped with two series connected filters (5 μ m+1 μ m), the surface roughness of the cut mold cavity can reach Ra 0.3 μ m. However, when there is no filtering or the filtering accuracy is insufficient, dense discharge pits and stripes will appear on the surface.

The circulating pump provides the power for circulating the working fluid, requiring stable flow and low pressure pulsation. Stainless steel centrifugal pumps with variable frequency control have become the mainstream choice due to their corrosion resistance and adjustable speed. When processing thin plates (thickness ≤ 10mm), using a higher spray pressure (1-2MPa) is beneficial for chip removal; When processing thick parts (thickness ≥ 100mm), it is necessary to appropriately reduce the pressure to prevent the electrode wire from swaying due to the impact of high-pressure liquid flow.

3.4 Components of wire transport mechanism

The wire transport mechanism is responsible for driving the electrode wire to move at a set speed, and its key components include the wire storage cylinder, wire feeding motor, reversing device, and tension adjustment system.

The wire storage tube is a unique component of fast wire cutting, used to store a certain length of molybdenum wire (usually 50-200m). The surface of the wire storage tube is provided with spiral grooves to guide the electrode wires to be arranged neatly, preventing wire stacking and disorder. The roundness, coaxiality, and dynamic balance level of the wire storage cylinder affect the smoothness of the electrode wire movement - when the jumping of the wire storage cylinder exceeds 0.02mm, the tension of the electrode wire will fluctuate periodically, and equidistant stripes will appear on the cutting surface. Excellent wire storage tube processing requires an outer circular runout of ≤ 0.005mm and a spiral groove lead error of no more than 0.02/300mm.

The tension adjustment system includes tension wheels, counterweights, springs, or servo motors. In fast wire processing, heavy hammer tension adjustment is often used - a constant tension is generated by hanging weights, and then applied to the electrode wire through a turning wheel. This structure is simple and reliable, but the inertia impact at the moment of reversal is significant, resulting in a slightly wider cutting seam at both ends of the workpiece than in the middle. Slow wire walking adopts servo tension control, with real-time feedback from a high-sensitivity tension sensor (resolution 0.1g) and servo motor driven tension wheel adjustment to control tension fluctuations within ± 1g. This precise tension control is the basis for achieving "one-time cutting and shaping" and "multiple cutting and polishing" processes with slow wire walking.

The wire motor drives the movement of the electrode wire. The fast wire walking adopts an AC variable frequency motor to achieve high-speed wire walking of 8-12m/s, with a commutation time of about 0.3-0.5 seconds. The high-frequency start stop ability of the motor directly affects the smoothness of commutation. Slow walking wire adopts a DC brushless motor to drive the electrode wire to move in a unidirectional low-speed direction (0.5-15m/min), which requires higher stability of the motor's low-speed torque.

3.5 High frequency pulse power module

High frequency pulse power supply is the "energy heart" of wire cutting processing, and its key components include power switch tubes (IGBT or MOSFET), pulse transformers, current limiting resistors, and waveform control circuits. The stability of pulse energy, the adjustable range of pulse width and pulse spacing, and the purity of waveform determine the controllability of the discharge process.

Modern wire cutting power supplies use equal energy pulse technology, where each discharge pulse delivers consistent energy to the machining gap, unaffected by changes in gap state. This requires power switching transistors to have high-speed switching characteristics (switching frequency 100-500kHz) and low on resistance (≤ 10m Ω). Pulse transformers are used for isolation and impedance matching, and the distributed capacitance and leakage inductance of their windings affect the steepness of the pulse front - the steeper the front, the better the discharge concentration, and the lower the surface roughness.

The high-frequency power module generates a large amount of heat during operation, and the design of heat dissipation components is crucial. High power IGBT modules require the installation of aluminum fin heat sinks and temperature controlled fans to ensure that the junction temperature does not exceed 125 ℃. Overheating can cause damage or premature aging of the switch tube, resulting in unstable power output, directly manifested as a decrease in cutting speed or frequent wire breakage.

4、 The relationship between component defects and wire cutting processing quality

In actual production, the degradation of component performance or improper selection is the main root cause of quality problems in wire cutting processing.

Case 1: The wear of the guide wheel leads to taper error. A certain mold company used fast wire cutting to process precision progressive molds with irregular convex molds (thickness 40mm). After cutting, the measured taper of the convex mold contour reached 0.015mm/100mm, exceeding the design allowable 0.005mm/100mm. After inspection, it was found that the V-shaped grooves of the upper and lower guide wheels have worn out grooves with a depth of about 0.1mm. After replacing the new guide wheel and re aligning the electrode wire, the taper error was restored to 0.003mm/100mm.

Case 2: Poor filtration of working fluid leads to surface degradation. During the mass processing of hard alloy top hammers, random black spots and stripes appear on the surface of slow wire cutting. By detecting the conductivity of the working fluid (which has risen to 85 μ S/cm) and analyzing the particle size of the electroerosion product (over 80% of particles are larger than 10 μ m), it was confirmed that it was caused by filter blockage and failure. After replacing the filter element with a precision of 1 μ m and adding deionized resin, the conductivity of the working fluid decreased to 12 μ S/cm, and the machined surface returned to the normal level of Ra 0.35 μ m.

Case 3: Over cutting caused by deviation in electrode wire diameter. A certain enterprise purchased a batch of molybdenum wire with a nominal diameter of 0.18mm. During actual cutting, it was found that the cavity size of the concave mold was about 0.02mm off. Using a micrometer to inspect the molybdenum wire, it was found that the diameter fluctuated between 0.183 and 0.186mm, significantly exceeding the acceptance standard of ± 0.0015mm. After replacing the molybdenum wire that meets the standards, the cutting size returned to normal.

These cases demonstrate the special importance of component quality control in online cutting and processing. Due to the invisibility of the wire cutting process, changes in the status of components such as electrode wires, guide wheels, and working fluids are often indirectly reflected through the quality of the final workpiece. Therefore, preventive maintenance and regular replacement are necessary measures to ensure machining consistency.

5、 The technological innovation trend of wire cutting components

5.1 Micro wire processing and electrode wire innovation

With the increasing demand for microelectromechanical systems (MEMS), microfluidic devices, and micro molds, wire cutting is extending towards the direction of microfabrication. Micro electrode wires with a diameter of 0.02-0.05mm have become a research hotspot, and the manufacturing accuracy of corresponding wire components (such as microporous diamond guides with a diameter of 0.03mm) has reached the sub micron level. At the same time, microstructure techniques for electrode wire surfaces, such as laser etched micro pits, are being developed to improve the uniformity of discharge distribution and enhance the stability of micro wire cutting.

5.2 Intelligent guide wire components

The intelligent guide wire system integrates micro force sensors and vibration sensors, which can monitor the force state and vibration amplitude of the electrode wire on the guide wheel in real time. When abnormal fluctuations are detected, the system can automatically adjust the tension setting value or issue a warning to replace the guide wheel/guide. A certain brand of slow-moving wire cutting machine has achieved "adaptive compensation for wire guide wear" - automatically correcting the offset of the cutting path based on accumulated processing time, cutting area, and discharge energy, extending the accuracy retention period by 40%.

5.3 Environmentally friendly working fluid components

Traditional slow wire processing uses deionized water. Although the medium itself is environmentally friendly, there is still environmental pressure in the treatment of electro corrosion products (containing heavy metals such as nickel, chromium, copper, etc.). A new type of biodegradable working fluid and its corresponding specialized filtration resin are currently under development. At the same time, the component design of closed-loop filtration systems tends towards modularity - quick change filter cartridges, resin tank bayonet connections, self-cleaning filters, etc., reducing the contact between operators and working fluids and improving the working environment.

5.4 Digital Twin and Component Life Prediction

Based on processing big data and digital twin technology, predictive analysis can be conducted on the health status of key components such as guide wheel wear, conductive block erosion, resin exchange capacity attenuation, and filter clogging degree. The system records the energy accumulation of each discharge, the length of the electrode wire passing through, the circulation rate of the working fluid, and other parameters, predicts the remaining life through machine learning models, and prompts replacement at the best time. This shift from "regular maintenance" to "condition based maintenance" can significantly reduce the loss of workpiece scrap and equipment downtime caused by sudden component failures.

VI. Conclusion

The application of online cutting and machining of components covers all aspects from discharge media (electrode wires) to energy supply (high-frequency power supply), from precision guidance (guide wheels/guides) to environmental maintenance (working fluid circulation system). The material, diameter, and surface characteristics of the electrode wire determine the basic level of cutting efficiency and surface quality; The accuracy of the guide wheel and guide device limits the geometric fidelity of the cutting path; The cleanliness of the working fluid and filtration system affects the achievement of processing stability and consistency; The tension control capability of the wire transport mechanism is directly related to the precision controllability of multi blade cutting.

With the continuous improvement of precision and surface quality requirements for parts in aerospace, precision molds, medical devices and other fields, wire cutting machining is continuously breaking through the technological boundaries of micro refinement, high-speed and intelligence. In this process, the performance improvement of components becomes a key driving force - the manufacturing accuracy of micro diamond guides, the discharge performance of coated electrode wires, the response speed of intelligent tension sensors, and the energy control accuracy of high-frequency power modules will all determine the core competitiveness of wire cutting equipment.

For operators and maintenance personnel of wire cutting equipment, a deep understanding of the functional positioning, failure modes, and replacement cycles of various components, and the establishment of a scientific preventive maintenance system, are effective ways to ensure processing quality, improve equipment utilization, and reduce production costs. In the future, with the deep integration of online monitoring, data analysis, and artificial intelligence technology with wire cutting components, "talking" guide wheels, "warning" filter elements, and "self optimizing" power modules will gradually enter engineering applications, promoting higher levels of intelligence and precision in electric discharge wire cutting machining.


Tel
15921227578 Liu Jinlin
Landline:021-69176937
Email
jinlinliu@bmzpmw.com
Headquarters Base
No. 58, Lane 355, Shengxin South Road, Nanxiang Town, Jiading District, Shanghai
Taicang Base
About 60 meters northeast of the intersection of Taicang City Pai Xin Chang Line and Xingang Road in Suzhou City
Customer Service WeChat
Copy successful
Contact
We are right beside you
Add WeChat and let us know your needs
Tel
15921227578
Top
Copy successful

WeChat ID: 400-000-8888

Add WeChat friends to get free
solutions and quotes

OK